Series 90-30 | Description |
IC690USB901 | GE PROGRAMMING CABLE |
IC693ACC300 | SERIES 90-30 16 point Input Simulator uses on slot in the base rack
requires minimal power |
IC693ACC301 | PLC Replacement Battery(qty 2) for all CPU's and PCM modules 2 per
package IC693ACC |
IC693ACC302 | GE 90-30 High capacity battery pack. IC693A mounted external
IC693AC IC693ACC 90-30 |
IC693ACC303 | Series 90-30 ACC303 Memory Card 32K for Hand Held Programmer
IC693PRG300 IC693A IC693ACC |
IC693ACC307 | GE TERMINATOR |
IC693ACC310 | 9030 Blank Filler Module for empty slots keeps dust out of all
connectors in the chs racks |
IC693ACC335 | GE Fanuc Terminal Block Axis for IC693DSM302 or IC693DSM314 90-30
Axis Control Analog Modules |
IC693ACC336 | Terminal Block for 90-30 Auxillary Module for the IC693DSM302 or
IC693DSM314 Axid 90-30 Modules |
IC693ACC337 | Terminal Block for Modules: IC693MDL654 IC693MDL655 IC693MDL752
IC693MDL753 - 32 Point Modules |
IC693ALG220 | Voltage Analog Input 4 Ch IC693A 0-10V IC693AL IC693ALG provides
four channels of input |
IC693ALG221 | Current Analog Input 4PT IC693A 4- 20 ma IC693AL IC693ALG provides
four channels input |
IC693ALG222 | High Density GE Analog Input 16/8 IC693A Voltage sixteen channels
single ended IC693ALG |
IC693ALG223 | High Density GE Analog Input 16 IC693A Current 4-20 ma allows 16
channels IC693ALG |
IC693ALG390 | Low Density GE Analog Voltage Output 2PT IC693A Module two ouput
channels IC693ALG |
IC693ALG391 | Low Density GE Analog Current Output module 2 channels 12 bit
resolution. IC IC693ALG |
IC693ALG392 | High Density GE Analog Output 8PT IC693A Current / Voltage allowing
eight single IC693ALG |
IC693ALG442 | Mixed Analog 4IN/2OUT IC693A Voltage or Current makes for versitle
module IC693ALG |
IC693APU300 | Series 90-30 High Speed Counter provides direct processing of rapid
pulse IC693 IC693APU |
IC693APU301 | AXIS POSTIONING Drive Enable Relay and Velocity Command outputs
IC693AP IC693APU |
IC693APU302 | APM MODULE Compatable with GE Fanuc Series 90-30 IC693 IC693A
IC693AP IC693APU |
IC693APU305 | I/O Link Module APU305 Modules are compatable with GE Fanuc Series
IC693AP IC693APU |
IC693BEM320 | I/O Link BEM320 Compatable with GE Fanuc Series 9030 PLCs IC693B
IC693BE IC693BEM |
IC693BEM321 | I/O Link master A module in the host provides the interface between
the FIP bus. IC693BEM |
IC693BEM330 | 90-30 BEM330 Bus Controller Module provide interface to a broad
range of discrete analog |
IC693BEM331 | 31 devices Genius Bus Controller I/O Link master I/O control
enhanced by communications |
IC693BEM332 | Series 90-30 FIP Remore I/O 2.5mhz Module is Compatable with 90-30
Series IC693BEM332 |
IC693BEM333 | GE Fanuc Series 90-30 Remote FIP Interface Module is Compatable
with 90-30 IC693BEM333 |
IC693BEM334 | Series 90-30 Genius Bus Controller Module is Compatable with 90-30
Series GE Fanuc PLC |
IC693BEM335 | GE Fanuc Series 90-30 FIP Remote I/O 2.5mhz Module is Compatable
with 90-30 IC693BEM |
IC693BEM340 | FIP Bus Controller Management of slave devices Monitoring of slave
devices IC693BEM |
IC693BEM341 | 2.5 MHZ FIP Controller The 2.5MHz version of requires a Release
8.10 version IC693BEM |
IC693CBK001 | 90-30 Cable Kit for High Density Modules I/O Includes the
IC693CBL327 IC693CBL328 - GE Fanuc Cables |
IC693CBK002 | Cable Kit for High Density I/O Modules (includes CBL329 and CBL330) |
IC693CBK003 | Cable Kit for High Density I/O Modules (includes CBL331 and CBL332) |
IC693CBK004 | Cable Kit for High Density I/O Modules (includes CBL333 and CBL334) |
IC693CBL300 | Rack Expansion Cable, I/O Expansion, 1 Meter |
IC693CBL301 | Rack Expansion Cable, I/O Expansion, 2 Meters |
IC693CBL302 | I/O Base expansion 50 feet (15 meters), continuous shield with
built in terminator. |
IC693CBL303 | Cable, Hand Held Programmer (HHP), 2 Meters |
IC693CBL304 | Cable, Port Expansion, Used With PCM300 |
IC693CBL305 | Cable, Port Expansion, Used With PCM301, PCM311, and CMM311 |
IC693CBL311 | I/O cable for DSM324 24V I/O or APM I/O to the 44A726268-001
terminal block. 3 meters |
IC693CBL312 | I/O rack expansion cable, 0.15 Meters, Shielded |
IC693CBL313 | I/O rack expansion cable 8 Meters |
IC693CBL315 | GE Fanuc 24 PIN Cable Assembly Three Meters for 90-30 Series
Modules Connection - GE Fanuc Cables |
IC693CBL316 | Station Manager Serial Cable for Ethernet TCP/IP |
IC693CBL319 | I/O cable for DSM324 24V I/O or APM I/O to the 44A726268-001
terminal block. 1 meter |
IC693CBL324 | I/O cable for DSM302 or DSM314 or DSM324 5V I/O. 1 meter |
IC693CBL325 | I/O cable for DSM302 or DSM314 or DSM324 5V I/O. 3 meters |
IC693CBL327 | Cable, Left Side, One - 24 Pin 90 Degree Connector, 3 Meter. |
IC693CBL328 | Cable, Right Side, One - 24 Pin 90 Degree Connector, 3 Meter |
IC693CBL329 | Cable, Left Side, Two - 24 Pin 90 Degree Connectors, 1 Meter |
IC693CBL330 | Cable, Right Side, Two - 24 Pin 90 Degree Connectors, 1 Meter |
IC693CBL331 | Cable, Left Side, Two - 24 Pin 90 Degree Connectors, 2 Meter |
IC693CBL332 | Cable, Right Side, Two - 24 Pin 90 Degree Connectors, 2 Meter |
IC693CBL333 | Cable, Left Side, Two - 24 Pin 90 Degree Connectors, .5 Meter |
IC693CBL334 | Cable, Right Side, Two - 24 Pin 90 Degree Connectors, .5 Meter |
IC693CHS391 | I/O Rack, 10 Slots GE Fanuc Automation Expansion remote Baseplate |
IC693CHS392 | I/O Rack, Expansion 10 Slots Remote baseplate has Rack Number
Selection DIP IC693CHS |
IC693CHS393 | I/O Rack, Remote Expansion CPU must be installed in slot 1
Expansion & Remote Baseplate |
IC693CHS397 | I/O Rack, CPU, 5 Slots Left slot supports Power Supply, Slot 1
supports CPU. IC693CHS 9030 |
IC693CHS398 | I/O Rack, Expansion, 5 Slots cable interconnection Expansion &
CPU baseplates IC693CHS |
IC693CHS399 | I/O Rack, Remote Expansion Basplates 25-pin female D-type I/O Bus
Expansion IC693CHS |
IC693CMM301 | Genius Communications configuration completed using Hand_held
Programme software IC69 |
IC693CMM302 | Communication card, Genius Series 90-30 PLC module, providing
Global Data IC693CMM |
IC693CMM304 | GE 90-30 Alstom N80 CMM304 high-performance microcomputer IC693CMM3
GE Fanuc |
IC693CMM305 | Alstom CMM305 ALSPA N80 Enhanced Comm Module Series Six PLC GE
Fanuc Serie IC693C |
IC693CMM311 | IC693CMM Communications Card user interfaces for the CMM311 and
CMM711 9030 |
IC693CMM321 | IC693CMM Modbus Ethernet Interface Transmit Data (TD) and Receive
Data (RD) 9030 |
IC693CMMAAUI | ETHERNET TRANSCIEVER CABLE FOR IC693CMM321-EE & EARLIER REVS |
IC693CPU311 | 5-slot baseplate with embedded CPU, 1K Byte Register Memory use
small fraction 9030 |
IC693CPU313 | 5-slot baseplate with embedded CPU, 2K Bytes Register
MemoryFirmware for CPUs 9030 |
IC693CPU321 | 10 SLOT CPU RACK Configuring a model 331 rack size will produce
Non-fatal hardware IC6 |
IC693CPU323 | 10-Slot Rack With Turbo CPU in base Firmware for these CPUs is in a
replaceable EPROM IC |
IC693CPU331 | CPU (16K Bytes) 10 MHz modular CPUs consist of a CPU, memory
IC693CPU Compatable |
IC693CPU340 | PROCESSOR CPU 80C188XL microprocessor 20 MHz, 32K Bytes User
Program IC693CPU 9030 |
IC693CPU341 | CPU341 module PROCESSOR 20 MHz, 80K Bytes User Program Memory
IC693CPU GE Fanuc |
IC693CPU350 | CPU 350 25 MHz Complimentary Metal-Oxide Semiconductor Random
Access Memory |
IC693CPU351 | CPU 351 Flash Firmware (Standard and User Memory) 25 MHz IC693CPU
Compatabe with |
IC693CPU352 | CPU 352 Capacities Speed: 25 Processor: 80386EX 25 MHz, math
coprocessor IC693CPU |
IC693CPU360 | CPU 360 Memory: 240K1 Confirgurable All Series CPUs can work with
integer numbers |
IC693CPU363 | CPU 363 CPU module, 25 MHz, with two extra serial ports 90-30 State
Logic CPU IC693CPU |
IC693CPU364 | CPU 364 and Ethernet Interface communicate without using the PLC
backplane IC693CPU |
IC693CPU366 | GE CPU 366 Module (240K Bytes configurable Supports Profibus DP
Master (Version 1 supported). One Profibus port and one RS-232
service port. |
IC693CPU367 | CPU 367 Module with PROFIBUS Slave Firmware 90-30 Embedded
Interface Series 90-30 CPU |
IC693CPU370 | GE CPU Ethernet CPU firmware stored in Flash memory loaded serial
port connector IC693CPU |
IC693CPU372 | CPU 372 CPU is modular, it can readily be replaced or changed to a
different type IC693CPU |
IC693CPU374 | CPU 374 CPU module, 133 MHz, 240K bytes User Program Memory with
Ethernet IC693CPU |
IC693DNM200 | DeviceNet Master Module allows a PACSystems RX3i to send and
receive I/O data IC693DNM |
IC693DNS201 | DeviceNet Slave Module support Get and Set PLC Registers IC693DN
IC693DNS Slave Module |
IC693DSM302 | 2 AXIS Motion Control 5v, 24v and Analog I/O Home Overtravel switch
inputs IC693DSM |
IC693DSM314 | 4 AXIS Control 3-4 Axis Analog Mode No Local Logic: 2.0msex
(position) Block Process IC693 |
IC693DSM324 | HI POWER 4 AXIS 1 DSM324i module CPU baseplate w/ PWR321/322/328
(20 per series) IC693 |
IC693MAR590 | IC693MAR 120Vac Input Relay Output DC load typical suppression
circuit IC693MA IC693MAR |
IC693MCM001 | IC693MCM001 In Stock! IC693MCM001 Digital Servo Interface Module
PDFsupply also repairs |
IC693MDL230 | 120 volts ac Isolated Input Module Circuitry Terminals Field in PDF
90-30 IC693M IC693MD |
IC693MDL231 | 240 Volts ac Isolated Input 8 Point Common Power Terminal Circuits
are Reactive 90-30 IC693 |
IC693MDL240 | 120 Volts ac Input Module 120VAC 16 Inputs Optical Coupler
Circuitry Wiring IC693 MDL IC693 |
IC693MDL241 | 24 Volts ac/Vdc Input Positive/Negative logic Input Module Field
Wiring Diagram in PDF IC693 |
IC693MDL250 | 120 VAC ISOLATED 16 PT INPUT Numbered LEDs show ON/OFF Status of
each Input IC693MDL |
IC693MDL260 | 120VAC 32 PT INPUT Filter Setup in PDF Grouped Input Module 32
Point 120VAC IC693MDL |
IC693MDL310 | 120 Volts ac Output, 0.5 Amp Connect Supplied Input Devices and
Power Sources Module |
IC693MDL330 | 120/240 Volts ac Output, 2 Amp 8 Point LEDs indicate ON/OFF Module
IC693MDL330 IC6 |
IC693MDL340 | 120 Volts ac Output, 0.5 Amp GE Fanuc Series 9030 Module IC693
IC693M IC693MD IC693 |
IC693MDL350 | 120/240 VAC ISOLATED OUTPUT, 2 AMP Module is Compatable with 90-30
Series IC693MDL |
IC693MDL390 | 120/240 Volts ac Isolated Output, 2 Amp Load Current vs Temperature
Output Module IC69 |
IC693MDL630 | Input MDL 24VDC Neg/Pos Logic 8 Pts Input Module 24 VDC
Negative/Positive Logic IC693 |
IC693MDL632 | 125 Volts DC Positive/Negative Logic Input Module Connections are
shown in dashed lines |
IC693MDL634 | 24 Volts dc Input, Negative/Positive Logic Module is Compatable
with 90-30 IC69 IC693MDL |
IC693MDL635 | GE Input module 125 VDC 16 point POS/NEG logic. Module does not
have UL certification. |
IC693MDL640 | 24Vdc Output Positive Logic 16 pts Module is Compatable with 90-30
Series MDL IC693MDL |
IC693MDL641 | 24 Vdc Output, Negative Logic Module is Compatable with 90-30
Series IC693MD IC693MDL |
IC693MDL643 | MDL643 9030 Input Module 24VDC 16 Point Positive 1MS Filter GE
Fanuc 90-30 IC693MDL6 |
IC693MDL645 | IC693MDL 24 Volts dc Input, Positive/Negative Module Logic Input vs
Temperature IC693M |
IC693MDL646 | 24 Volts dc Input, Neg/Pos Logic LEDs Indicate ON/OFF 8 Green Light
IC693MD IC693MDL |
IC693MDL648 | 48Volts dc Input, Neg/Pos Logic Module is Compatable with 90-30
Series IC693MD IC693MDL |
IC693MDL652 | GE FANUC INPUT MODULE 24VDC 32POINT -/+ 2MS |
IC693MDL653 | 24 Volts dc Input, Neg/Pos Logic MODULE Circuitry Connector
Terminals IC693MD IC693MDL |
IC693MDL654 | 5/12 Volts dc (TTL) Input, Neg/Pos Logic 32 Point Module 5/12 Volt
DC IC693MD IC693MDL |
IC693MDL655 | IC693MDL 24 Volts dc Input, Module Negative/Positive Logic 32 Point
IC693MD IC693MDL |
IC693MDL660 | 24VDC Input Module 32 point requires a terminal block IC694TBB032
TBS032 terminal |
IC693MDL730 | 12/24 Volts dc Output, 2 Amp, Positive Logic (8) Point Module 90-30
IC693MD IC693MDL7 |
IC693MDL731 | 12/24 Volts dc Output, 2 Amp, Negative Logic (8) Point Module for
9030 IC693MD IC693MDL |
IC693MDL732 | 12/24 Volts dc Output, 0.5 Amp, Positive Logic (8) Point Module
9030 IC693MD IC693MDL |
IC693MDL733 | 12/24 Volts dc Output, 0.5 Amp, Negative Logic (8) Point Module
9030 IC693MD IC693MDL |
IC693MDL734 | 125 Volts dc Output, (6) Point Module for Series 9030 GE Fanuc PLC
PDF IC693MD IC693MDL |
IC693MDL740 | IC693MDL 12/24 Volts dc Output, 0.5 Amp GE Fanuc PLC Series 90-30
IC693MD IC693MDL |
IC693MDL741 | 12/24 Volts dc Output, 0.5 Amp, Negative Logic (16) point Series
90-30 IC693MD IC693MDL |
IC693MDL742 | 12/24 Volts dc Output, 1 Amp, Positive Logic PLC GE Fanuc Series
90-30 IC693MD IC693MDL |
IC693MDL748 | 48Volts DC Output, 0.5 Amps, Positive Logic MDL Module Series 90-30
IC693MD IC693MDL |
IC693MDL750 | 12/24 Volts dc Output, Negative Logic MDL750 Module Series 90-30
IC693MD IC693MDL |
IC693MDL751 | 12/24 Volts dc Output, Positive Logic (32) Point MDL751 Module
90-30 IC693MD IC693MDL |
IC693MDL752 | 5/12/24 Volts dc (TTL) Output, Neg Logic, (32) Point Module MDL752
IC693MD IC693MDL |
IC693MDL753 | IC693MDL 12/24 Volts dc Output, Pos Logic (32) Point MDL753 Module
IC693MD IC693MDL |
IC693MDL754 | MDL754 9030 Output Module 12/24VDC for Series 90-30 Systems
IC693MDL IC693MDL75 |
IC693MDL760 | 9030 MDL760 Solenoid Value Out 11 pt. 24VDC Out 5 pt. Series 90-30
GE FANUC PLC IC693MDL IC693MDL7 |
IC693MDL916 | Output Module Isolated Relay 4 amp 16 point Requiers High Density
Terminal Block MDL916 |
IC693MDL930 | Soldered InRelay Output, Isolated, 4 Amp Series 90-30 MDL930 Module
IC693MD IC693MDL |
IC693MDL931 | Soldered InRelay Output 8 Amp GE Fanuc Series 90-30 MDL931 Module
IC693MD IC693MDL |
IC693MDL940 | Relay Output, 2 Amp (16) Point MDL940 Module GE Fanuc Series 90-30
IC693MD IC693MDL |
IC693MDR390 | IC693MDR 24Vdc Input Relay Output (8) Point MDR390 Module 90-30
IC693MD IC693MDR |
IC693NIU004 | ETHERNET NETWORK INTERFACE GE Fanuc Series 90-30 NIU004
ModuleIC693NI IC693NIU |
IC693PBM200 | Siemens Profibus DP Master Module PBM200 Series 90-30 Module Profi
IC693PB IC693PBM |
IC693PBS201 | Siemens Profibus DP Slave Module PBS201 Module Series 90-30 Profi
Bus IC693PB IC693PBS |
IC693PCM300 | Programmable Coprocessor Module (PCM) 160 KB PCM300 Series 90-30
IC693P IC693PC |
IC693PCM301 | IC693PCM PCM 192 KB Programmable Coprocessor Module (PCM) 301
IC693P IC693PC |
IC693PCM311 | PCM Programmable Coprocessor Module (PCM) 311 Series 90-30 640 KB
IC693P IC693PC |
IC693PRG300 | IC693PRG 90-30 Hand Held Programmer PRG300 Compatable with 9030
IC693P IC693PG |
IC693PRG301 | IC693PRG 90-30 Hand Held Programmer PRG301 Compatable with 9030
IC693P IC693PG |
IC693PTM101 | Power Transducer Module Compatable with Series 90-30 PTM101 IC693
IC693P IC693PT |
IC693PWR321 | 30 Watt PS 120/240 Vac 125 Vdc Power Supply Unit Module Series 9030
IC693P IC693PW |
IC693PWR322 | DC Powered Supply, 24/48 Vdc PWR Supply Unit Module Series 90-30
IC693P IC693PW |
IC693PWR324 | Alstom Power 30 Watt PS 120/240 Vac 125 Vdc PWR324 Supply 90-30
IC693P IC693PW |
IC693PWR325 | Series 90-30 Power Supply PWR325 24/48 Vdc 30 Watts IC693PWR32
IC693PWR |
IC693PWR328 | Power Supply, 48 Vdc PWR328 GE Fanuc Series 90-30 Power Supply
IC693P IC693PW IC693 |
IC693PWR330 | High capacity PS 120/240 Vac 125 Vdc Power Supply PWR330 90-30
IC693P IC693PW IC693 |
IC693PWR331 | Power Supply, 24 Vdc, High Capacity Power Supply PWR331 Series
90-30 IC693P IC693PW |
IC693PWR332 | Power Supply, 12 Vdc, High Capacity PWR332 Series 9030 PWR Supply
IC693P IC693PW |
IC693TCM302 | Temperature Control Module TCM302 Series 90-30 IC693 IC693T
IC693TCM IC693TCM3 |
IC693TCM303 | Temperature Control Module (TCM) 8 T/C In/ 8 DC Out 18 to 30 volts
DC |